CQC14 Pop on Frame Lock installed

Please note that this job shown here known as a frame lock conversion along with some others I used to offer are no longer being done by me. I will not be offering this service for production models or the services of rebuilding lock back style folders like some of the Spydercos shown here and this is something that I just decided not too long ago. The reasons for this are too lengthy to get into here. I leave what is shown here in these posts in my blog for your viewing pleasure only. At this time I am trying to focus more on my custom folders which I make from scratch. I will continue to offer my custom folders and my custom titanium pocket clips and pry bars as well but I have limited the numbers of these I will do at one time also. If you wish to know more about why, or what other jobs just write me or post a question in a comment. Thanks for understanding.

My first post for 2010 is shown here and it is one of the pop on frame lock sides in .160 thickness 6AL-4V titanium I did for folks a while back. This is left over from last year. This was made for the Emerson CQC14 model without even having the knife shown here in the picture here to use but simply by doing all the same prep work as if I did have the knife here and then shipping the frame out to the owner of the knife to install himself.

The holes are all mated up to match up perfectly to the original factory side so all the user has to do is open this lock, disassemble their folder and reassemble it using the new thicker slab instead of the original factory thin liner lock and G10 scale.

Some of the models have been tricky to do this with but the 14 and the Horseman have both proven to be quite consistently identical from Emerson so I have had success with several now doing them this way for folks. The owner of the knife then installed the lock side and new replacement non rattle stop pin and took these pictures.

Oh and by the way. I appreciate the great pictures. They always look so much better when someone else takes the pictures so I can post them here.

Thanks

STR

Lignum Vitae Spyderco Stretch w/ ti liners.

This is one I did a long time ago and should have loaded up here on my blog a long time ago as well. I am really surprised this Spyderco Stretch was not added because the lignum vitae handle scales I did for it and the ti liners for a complete rebuild of the body really added a lot of class to this folder. Its probably one of the better Spyderco models that left my shop after completing the job. The gentle feathering pattern of this particular slab of wood I had when this was done really came out so nice it surprised everyone. With age the handles have darkened some with exposure to sunlight which is a typical reaction for this wood once it is aged.

It is normally the case that when you add lignum to a folder the knife gains some weight but since this one was all stainless before it really equaled out quite well in the end. As is shown here the knife was not equipped with a pocket clip. The owner, the Deacon on blade forums and the Spyderco forums didn't want one and does not use one at all. The R2 model I did that is posted in another thread in older posts from 09 below belongs to the the Deacon and the Atlantic Salt in stabalized birds eye maple scales with titanium liners in a 2008 post belongs to him as well.

Thanks for looking

STR

Low Rider Pocket Clips For Folding Knives

Update: Jan, 2016. see here for clip info. See below for updates. Older but current clip info.
See here for Prybar info.  Mini Ti Pry order info


 I like doing the clips on some models for folks when people call for them. I recently found some blanks I had cut out that I may as well use. Those include Para 2, Military and Para Military original, JYDII, Leek and Southard patterns that I have which I can still do. These are 35 each via check or money order or 40 for the first and 35 for each additional clip after that first via pay pal at http://paypal.me/StephenRice

 As I have always said I'll do them as long as they are called for.. In this case I will do them until the bags found are used up. After that we'll go from there. Thanks
STR

Mini Titanium Prybars

Seen here are some .090 thickness 6Al-4V grade 5 titanium prybars I started making a few years ago. Call these the first generation. See my newest posting on these for the current ones being made. http://strsbackyardknifeworks.blogspot.com/2011/02/mini-ti-pry-info-thread.html

All my new ones are being done withe V nail pull in the end now and since doing this they are $30 shipped. These started out as a smart way to use up some scrap left over end cuts of titanium sheets I had from folding knifemaking but that were too small to use for folders. It didn't take me long to realize there was a market for them albeit a small one. I don't make that many these days like I did when I first started offering them but when I do make a batch they don't last long usually. I'm down to six remaining from this batch at this writing, most of which sold before I even got the pictures loaded everywhere I wanted to put them. Go figure.

Anyway, these are great stocking stuffers for Christmas and make great gifts for other times. These are usually just as fast getting there first class and its cheaper than Priority so that is how I mail them unless you wish to pay for Priority mail. If so just advise of this when you order.. International shipping is a case by case basis and you need to contact me first to work out how that will be done and the cost.

These are available in a variety of colors as you can see and each one is slightly different as I do still do these up from base raw materials all by hand from scratch. While the video below shows me grinding one it does not show the steps involved just to get to that step where I can now grind. Before that I have to drill progressive holes, finish the holes with a 83 degree drill and then cut that bar in half which is also one of my public videos showing me cutting the strips that give me two bars each to grind. I wrap them either in para cord or some other decorative nylon cord wrap which you can pick for yours should you buy one. This cord helps to aid grip and looks, as well as, allow one to carry them on key rings.

I have been told my pry bar is quite handy. They have been popular with a niche group most often popular with folks working in 'non knife' office environments or where "sheeple" friendly attire is needed like a public job where they are seen a lot. Also, some people like having a tool on them besides their knife and don't particularly want to use their knife for jobs that will ding the edge all up or break the tip so this little tool here fits the bill and can actually open boxes and pop tape to separate it from the roll or lift a tab, as well as, pry staples and other things doing the stuff folks want done. I've also sold some of these prybars to police officers that use them as PI (private investigation) probes for evidence gathering and investigation work at crime scenes to dig around in places they don't necessarily want to touch with their fingers. Apparently titanium is preferred because it is an inert metal and will not contaminate the crime scene. The way I make these they are actually equipped with a flat head screwdriver on one end and a pry bar on the other. Many folks that carry Emerson folding knives like these for the flat head screwdriver; as they can use their pry bar to adjust their pivot screw tension. If you are familiar with Emerson knives you are surely aware that the pivot tends to loosen over time so these can be quite handy to have around on your key ring if you happen to carry an Emerson folding knife.

These pry bars, while not what I'd call extreme heavy duty are still plenty thick titanium so they do hold up quite well and you can actually get rough with them. Believe me people have done so and then told me about it. I have customers that use them from all over the world at this point and while they are certainly not what I'd call a hot seller they do seem to serve a purpose for some so if one interests you here let me know. I had one email recently from a Dept. of Defense Col. just back from Afghanistan and he told me a story of how one of these little simple tools likely saved lives opening up stubborn wooden ammo crate lids when they could not force it otherwise allowing ammo to get to hands just in time according to him. I tell ya, it kind of choked me up a bit to think that this simple tool could have that kind of a profound effect on someone but apparently that is the case. If you like the idea but wanted a heavier one or one longer maybe, well, I may have some thicker scraps of titanium in the shop from folding knife making and other things I'm into so just ask. I'm easy to reach by email and that seems to work best for me.

Thanks for looking. Oh and for anyone curious see the video below on how I do theses. Sorry my help hit the button to shut it off before even showing the pry bar I just completed grinding. Other than this and some last footage jerkin around when I was hitting my signature punch she did a stand up job on the video. Enjoy. 

STR